Loaderbig

Setup and operation

How do I use the Cycle preset? Cycle Preset Loop alternations from minimum to maximum power. Adjusting its parameters you can obtain…

Cycle Preset 

CYCLE White Loop alternations from minimum to maximum power.

Adjusting its parameters you can obtain different effects (wave, cross-wave, gyre, ...).

Parametres Preset Cycle 01

MIN (%): minimum power value (in percentage)

MAX (%): maximum power value (in percentage)

T MIN (sec): stable duration at minimum power (in seconds)

T MAX (sec): stable duration at maximum power (in seconds)

T RISE (sec): transition time to pass from MIN to MAX (in seconds). Min value of 0.25

T FALL (sec): transition time to pass from MAX to MIN (in seconds). Min value of 0.25

 
NOTE: Minimum pulse duration can result in 0,5 sec

 

Learn how to create waves in your aquarium using the Cycle preset.

 

Watch the video tutorial 

Youtubesubscribe

Preset Types

 

Can I create waves with Waver in my aquarium? Yes of course, Waver is designed to recreate the natural ocean currents on coral reef.…

Yes of course, Waver is designed to recreate the natural ocean currents on coral reef. There can be different effects you can obtain with the Mover + Waver.

CYCLE White Use the Preset "Cycle" and edit the adjustable parameters to obtain the desired wave.


Some suggestions:

- The higher is the difference between MIN% - MAX%, the better is the wave effect (example 1% - 100% ) 

- TRISE and TFALL: leave these parameters at minimum (0,25 sec)

- TMIN and TMAX: this values change accordingly to the length of the tank and the pump models. This defines the increase / decrease in waves level. 

 

Examples:

Wave effect

- Movers' placement: opposite short sides

- MIN%: 1     MAX%: 100

- TRISE / TFALL (sec): 0,25 

- TMIN / TMAX (sec): 

  • Tank length -> 60cm [24in] -> 0,22*
  • Tank length -> 90cm [35in] -> 0,32*
  • Tank length -> 120cm [47in] -> 0,43*

- CH1 not inverted CH2 inverted

*Average values of maximum wave. Surrounding values will result in a lower wave effect.

Try to increase / decrease these values to obtain the desired wave and wait 20-30 seconds to let the wave stabilize.

Watch the video tutorial 

Wave Effect

Youtubesubscribe

 

Cross-wave effect

- Movers' placement: opposite short sides

- MIN%: 1     MAX%: 100

- TRISE / TFALL (sec): 0,25 

- TMIN / TMAX (sec): 

  • Tank lenght -> 60cm [24in] -> 0,06*
  • Tank lenght -> 90cm [35in] -> 0,10*
  • Tank lenght -> 120cm [47in] -> 0,14*

- CH1 not inverted CH2 not inverted

*Average values of maximum wave. Surrounding values will result in a lower wave effect.

Try to increase / decrease these values to obtain the desired wave and wait 20-30 seconds to let the wave stabilize.

Watch the video tutorial 

Waver Cross Wave

Youtubesubscribe

 

Gyre

- Movers' placement: opposite long sides

- MIN%: 1     MAX%: 100

- TRISE / TFALL (sec): 0,25 

- TMIN / TMAX (sec): 

  • Tank width -> 30cm [11in] -> 0,04*
  • Tank width -> 45cm [17in] -> 0,08*
  • Tank width -> 60cm [24in] -> 0,12*

- CH1 not inverted CH2 not inverted

*Average values of maximum wave. Surrounding values will result in a lower wave effect.

Try to increase / decrease these values to obtain the desired wave and wait 20-30 seconds to let the wave stabilize.

Watch the video tutorial

Create Gyre Waver

Youtubesubscribe
How do I adjust the time of Waver? Click on CONFIGURATION MENU -> GENERAL -> adjust the time and SAVE. Watch the video…

Click on CONFIGURATION MENU -> GENERAL -> adjust the time and SAVE.

 

Watch the video tutorial

Setup Waver